廣東美國分析儀價格

LECO—Your source for total analytical solutions

CS CS 844 and 744 Series: Carbon/Sulfur by Combustion

Carbon and sulfur determination by combustion infrared detection

Quick, accurate, and affordable determination for both production control and research

Calibration, analysis, evaluation, and diagnostic functions accessible via user-friendly brand software

GDS GDS 500A and 850A Atomic Emission Spectrometers

Spectral range from 120 to 800 nm

Continuous profile of concentration/thickness

Large, dynamic range with concentrations from ppm to 100% by weight

Short analysis time (minutes)

氧氮氫分析儀選哪家？給您推薦上海禹重！廣東美國分析儀價格

Procedure - Solid Samples

Press the Analyze button on the instrument screen again, the loading head slide-block will close and the lower electrode will open.

Clean the upper and lower electrode manually, or, if applicable, remove the crucible and press the analyze button to clean with the automatic cleaner

Add approximately 0.05 g of *** Graphite Powder to a *** Graphite Crucible.

Firmly place the crucible on the lower electrode tip or appropriate autoloader position.

Press the Analyze button on the instrument screen, the lower electrode will close and the analysis sequence will start and end automatically

力可OHN736&836系列儀器采用惰性熔融法，提供各種無機材料、鋼鐵、有色金屬、硬質合金陶瓷材料中寬范圍的氧氮氫同時測定。ONH836儀器通過***采納客戶的反饋意見和創新設計，力可***儀器采用觸摸屏技術和在線軟件平臺，增強了儀器的可操作性，降低了分析成本，節省實驗室桌面空間。

用戶友好界面的Cornerstone? 軟件

力可**的Cornerstone碳硫分析軟件采用觸摸屏界面使用戶可完整的達到分析控制、方法設定、在線診斷、數據報告。Cornerstone碳硫分析軟件允許用戶在單一分析界面中完成日常的所有工作，快速而且簡單易用。力可創新的批次和重復樣品數據分組功能極大簡化了樣品結果輸出和結果標準偏差的自動計算。減少了繁瑣的額外數據處理。

氧氮氫分析儀的常見故障及解決方法

供電正常、通訊正常，點擊確認鍵后分析儀不工作。這是沒有水流，爐子溫度太高或儀器通道電壓不正常。如沒有水流，爐子溫度太高這些信息會顯示在顯示器畫面上，但沒有信息顯示說明這兩項正常。接下來檢查儀器通道零位電壓，如果比±3V高出1V以上，可能是因為氣瓶空了，或者是空氣進入到分析儀中。檢查并更換化學試劑，如果有空氣進入熱導池里，熱導池的電壓就會＜-6V，此時打開右面的門，堵住爐子氣體進口，10s后，熱導池電壓值必然升高。經過逐一排查，**終確認堿石棉有問題，更換后儀器正常。 穩固的爐頭試樣加載結構。

Summary

The determination of the amount of oxygen, nitrogen, and hydrogen in iron, steel, nickel-, and cobalt-base alloys represents some of the most important quality metrics for these materials. Oxygen is used to create steel from pig iron by removing excess carbon. Oxygen content must be controlled to limit the amount of carbon monoxide that can be formed during solidification which may cause excessive porosity. Nitrogen is considered both an impurity as well as an important alloying agent. Itcan be present as a nitride or interstitially in its gaseous form. Increased nitrogen content is known to increase yield and tensile strength, thus decreasing ductility and formability. Excessive levels may evolve during solidification thus increasing porosity. High hydrogen content is the primary cause of embrittlement, blistering and flaking due to its high

mobility through the lattice and provides no potential alloying benefits. The ONH836 utilizes a high-power

electrode furnace to quickly and efficiently release the target gases from within the sample, which allows

for a very rapid simultaneous determination of oxygen, nitrogen, and hydrogen.

***紅外池的恒溫絕熱技術消除了外界環境溫度的干擾。廣東美國分析儀價格

可以旁路的OMI-2 氣路強化過濾裝置增強了檢測器的穩定性，使得分析結果更加準確。廣東美國分析儀價格

Instrument Highlights and Features

Optional Features

Optional boom-mounted touch-screen interface package (M) promotes an ergonomic workspace

Optional Performance Package (P) adds a three-stage carrier gas purification system, and a dual-loop gas dose module

Optional Dual Cooling Package (D) adds an integratedliquid-to-air radiator with dual cooling fans. This DC

option gives the user the choice of liquid-to-liquid cooling, liquid-to-air cooling, or a combination of both

Optional integrated autocleaner (H) automatically cleans the upper electrode and lower electrode tip

Optional 20-sample shuttle loader available

廣東美國分析儀價格